Membrane drip irrigation yield-increasing technology is the integration of advanced irrigation technology and fertilization technology. It not only exerts the effect of mulching cultivation to increase ground temperature and reduce evaporation between trees, but also realizes on-demand irrigation and fertilization of corn, and uniformly and continuously transports water and nutrients. The soil near the roots is absorbed by the root system to improve the utilization rate of water and fertilizer, and achieve the purpose of increasing production and increasing efficiency. The technical content mainly includes the cultivation of drip irrigation system and the cultivation and cultivation technology of corn under drip irrigation conditions. Technical points: Fine ground preparation Before planting, the ridges are ridged and cultivated in wide and narrow rows. Generally, the narrow behavior is 40 to 50 cm and the width is 60 to 80 cm. The smashing machine is used for smashing or deep-spinning, and the depth of ploughing should reach 20 to 25 cm. Generally, 1000-2000 kg of high-quality agricultural fertilizer, 15-20 kg of diammonium phosphate, 5-10 kg of potassium sulfate or 30-40 kg of compound fertilizer are used as the base fertilizer. The landscreting operation of the whole land is completed once by the large-scale combined soil preparation machine, and the land preparation effect is good. Laying drip irrigation pipes According to the location of the water source and the shape of the land, the main pipeline laying methods are mainly independent and composite: the independent main pipeline laying method has the advantages of labor saving, material saving and simple operation, but it is not suitable for large-area operation; The laying of the composite main pipe can carry out large-area drip irrigation operations, requiring the water source to be close to the land, and the field has a fixed place for power supply. There are two types of branch pipes: direct connection method and indirect connection method. The direct connection method has low input cost but large water pressure loss, resulting in uneven soil moisture; the indirect connection method has the characteristics of flexibility and operability, but increases the control, connecting parts and other components, and the one-time input cost is increased. The speed and quality of drip irrigation with a distance between 50 and 70 meters is the best. Scientific selection and reasonable densification The mulching film is covered by drip irrigation, and the varieties with dense density and growth period are 7 to 10 days longer than the open varieties, and the effective accumulated temperature is 150 to 200 °C. Seed treatment is carried out in a conventional manner before sowing. Reasonable increase in planting density, the amount of seed used is 15% to 20% more than the common planting method. Fine seeding When the plough layer is 5 to 10 cm and the temperature is stable and passed through 8 ° C, it can be ploughed. With a film having a thickness of 0.01 mm, the width of the film is determined according to the width of the ridge. According to the seeding method, it can be divided into two types: membrane seeding and membrane seeding. 1. Sowing on the membrane: seeding with multi-purpose precision seeding machine under drip irrigation with corn film, spraying drip irrigation belt, spraying herbicide, covering the ground film, sowing, soiling and repressing operations, the operation sequence is drip irrigation belt → Spraying herbicides → covering the ground film → sowing → soiling → suppression. 2. Seeding under the membrane: mechanical sowing, semi-mechanical sowing and artificial sowing can be used. After the sowing, the herbicide is sprayed on the ridge by the machine, and the film should be coated in time after spraying. The soil on both sides of the mulch should be sufficient to press the soil on the membrane every 3 to 4 meters to prevent the wind from blowing up the membrane. Seeding under the membrane should pay attention to timely introduction of seedlings and seedlings: When the corn is generally seeded with 1 or 2 pieces, the seedlings are introduced in time, and the seedlings are covered with wet soil after the seedlings are introduced. After another 3 to 5 days, the seedlings will be taken out. Strengthen field management Under the drip irrigation of corn film, it is necessary to check whether the film is strict or not. If it is found that there is damage or soil pressure is not correct, it is necessary to use the soil pressure in time to prevent it from being blown away by the wind to ensure heat preservation. Drip irrigation according to the water requirement of corn crops. 1. Drip irrigation: After the equipment is installed and commissioned, it can be irrigated according to the soil moisture. Each hectigation is 1 hectare. The number of “zones†opened once is calculated according to the length of the capillary. The first working pressure is within 2 pressures, generally 10-12. Hours of irrigation, then you can switch to the next irrigation area. 2. Topdressing: According to the characteristics of corn required for water, the fertilizer is put into the fertiliser according to the proportion, fertilizing with water, preventing premature defamation and premature aging, and improving the utilization rate of water and fertilizer. The amount of fertilizer used in each irrigated area should be calculated, the fertilizer dissolved in a large container, and the solution poured into a fertiliser tank. 3. Chemical control: Due to high planting density, high temperature, sufficient water, and rapid growth of plants, in order to prevent the plant from growing too high and causing lodging, it should be controlled in the 6 to 8 piece leaf stage. 4. Appropriate late harvest: In order to fully mature the corn, reduce the water, and improve the quality, it can be harvested as appropriate according to the specific conditions at the time of harvest. Disclaimer: Some articles on this website are transferred from the Internet. If legal rights of third parties are involved, please inform this website. phone
Suyzeko Photobiomodulation Therapy Helmet 810nm Infrared Helmet PBM Light Therapy Machine
infrared red light helmet 810nm Photobiomodulation benefits and photobiomodulation therapy near me
Photobiomodulation (PBM) describes the use of red or near-infrared light to stimulate, heal, regenerate, and protect tissue that has either been injured, is degenerating, or else is at risk of dying. One of the organ systems of the human body that is most necessary to life, and whose optimum functioning is most worried about by humankind in general, is the brain.
PBM light therapy, also known as photobiomodulation therapy, has been shown to have several benefits for brain disorders. This therapy involves using low-level light therapy to stimulate the cells in the brain and promote healing and regeneration. Here are some of the benefits of PBM light therapy for brain disorders:
photobiomodulation, pbm light therapy,photobiomodulation therapy machine,Infrared Helmet,810nm 1070nm pbm helmet, rtms helmet Shenzhen Guangyang Zhongkang Technology Co., Ltd. , https://www.szlighttherapymachine.com
1. Neuroprotection: PBM light therapy has been found to have neuroprotective effects, meaning it can protect the brain cells from damage and degeneration. It can help reduce inflammation and oxidative stress in the brain, which are common factors in many brain disorders.
2. Improved cognitive function: PBM light therapy has been shown to enhance cognitive function, including memory, attention, and problem-solving skills. It can stimulate the production of brain-derived neurotrophic factor (BDNF), a protein that promotes the growth and survival of brain cells.
3. Reduced symptoms of depression and anxiety: PBM light therapy has been found to have antidepressant and anxiolytic effects. It can increase the production of serotonin, a neurotransmitter that regulates mood, and reduce the activity of the amygdala, a brain region involved in fear and anxiety.
4. Enhanced neuroplasticity: PBM light therapy can promote neuroplasticity, which is the brain's ability to reorganize and form new connections. This can be beneficial for individuals with brain disorders as it can help improve their ability to learn, adapt, and recover from injuries.
5. Accelerated healing after brain injuries: PBM light therapy has been shown to accelerate the healing process after brain injuries, such as traumatic brain injury or stroke. It can improve blood flow to the injured area, reduce inflammation, and stimulate the repair and regeneration of damaged brain cells.